Mechanics of Composite, Hybrid and Multifunctional Materials, Volume 5

Proceedings of the 2018 Annual Conference on Experimental and Applied Mechanics

Piyush R. Thakre, Raman P. Singh, Geoffrey Slipher

• Publisher: River Publishers
• Year: 2025
• eBook ISBN:
  9781040602867
• Topic: Physical Sciences

Mechanics of Composite, Hybrid, and Multifunctional Materials, Volume 5 of the Proceedings of the 2018 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the fifth volume of eight from the Conference, brings together contributions to this important area of research and engineering. The collection presents early findings and case studies on a wide range of areas, including:
Recycled Constituent Composites
Nanocomposites
Mechanics of Composites
Fracture & Fatigue of Composites
Multifunctional Materials
Damage Detection & Non-destructive Evaluation
Composites for Wind Energy & Aerospace Applications
Computed Tomography of Composites
Manufacturing & Joining of Composites
Novel Developments in Composites.

Table of contents

• Cover
• Series Page
• Frontmatter
• Title Page
• Copyright Page
• Preface
• Table of Contents
• 1 Stimulus-Responsive Interfacial Chemistry in CNT/Polymer Nanocomposites
• 2 Devulcanized Rubber Based Composite Design Reinforced with Nano Silica, Graphene Nano Platelets (GnPs) and Epoxy for “Aircraft Wing Spar” to Withstand Bending Moment
• 3 Study of Mechanical Characteristics of Banana and Jute Fiber Reinforced Polyester Composites
• 4 Toughening Mechanism in Epoxy Resin Modified Recycled Rubber Based Composites Reinforced with Gamma-Alumina, Graphene and CNT
• 5 AlSi10Mg Nanocomposites Prepared by DMLS Using In-Situ CVD Growth of CNTs: Process Effects and Mechanical Characterization
• 6 Optimization of Surface Integrity of Titanium-Aluminum Intermetallic Composite Machined by Wire EDM
• 7 Design of Cost Effective Epoxy + Scrap Rubber Based Composites Reinforced with Titanium Dioxide and Alumina Fibers
• 8 Reinforcement of Recycled Rubber Based Composite with Nano-Silica and Graphene Hybrid Fillers
• 9 Testing the 2-3 Shear Strength of Unidirectional Composite
• 10 Nondestructive Damage Detection of a Magentostricive Composite Structure
• 11 Thermo-Mechanical Properties of Thermoset Polymers and Composites Fabricated by Frontal Polymerization
• 12 Design of Magnetic Aluminium (AA356) Composites (AMCs) Reinforced with Nano Fe3O4, and Recycled Nickel: Copper Particles
• 13 Reinforcement Effect of Nano Fe3O4 and Nb2Al on the Mechanical and Physical Properties of Cu-Al Based Composites
• 14 Recycled Ti-17 Based Composite Design; Optimization Process Parame ters in Wire Cut Electrical Discharge Machining (WEDM)
• 15 Alternative Composite Design from Recycled Aluminum Chips for Mechanical Pin-Joint (Knuckle) Applications
• 16 Manufacturing of Copper Based Composites Reinforced with Ceramics and Hard Intermetallics for Applications of Electric Motor Repair Parts
• 17 Damping and Toughening Effect of the Reinforcements on the Epoxy Modified Recycled + Devulcanized Rubber Based Composites
• 18 Impact and Post-impact Behavior of Composite Laminates Reinforced by Z-Pins
• 19 Layered Jamming Multifunctional Actuators
• 20 2D Microscale Observations of Interlaminar Transverse Tensile Fracture in Carbon/Epoxy Composites
• 21 Electro-Mechanical Response of Polymer Bonded Surrogate Energetic Materials with Carbon Nanotube Sensing Networks for Structural Health Monitoring Applications
• 22 Strength and Energy Absorption Capability of Porous Magnesium Composites Reinforced by Carbon Nanofibers
• 23 Mechanical Characterization of Open Cell Aluminum Foams Using X-ray Computed Tomography
• 24 Damage Detection and Visco-Elastic Property Characterization of Composite Aerospace Panels Using Ultrasonic Guided Waves
• 25 Microscale Investigation of Transverse Tensile Failure of Fiber-Reinforced Polymer Composites
• 26 Optimization of Kerf Quality During CO2 Laser Cutting of Titanium Alloy Sheet Ti-6Al-4V and Pure Titanium Ti
• 27 A Study of the Surface Integrity of Titanium Alloy Ti-6Al-4V in the Abrasive Water Jet Machining Process
• 28 Process Reliability of Abrasive Water Jet to Cut Shapes of the Titanium Alloy Ti-6Al-4V
• 29 Optimization of the High Energy Milling Process of Chips of a Stainless Steel Using the Response Surface Modeling
• 30 Iron Contents on Recycle Aluminum and Influence on Mechanical Properties
• 31 Experimental Comparison of the Microstructure and Surface Roughness in CO2 Laser Cutting of the Titanium Alloy Ti-6Al-4V and the Pure Titanium Ti
• 32 Influence of Crumb Rubber Reinforcement on the Properties of Medium Density Fiberboard
• 33 Sub-components of Wind Turbine Blades: Proof of a Novel Trailing Edge Testing Concept
• 34 Toughening Mechanisms on Recycled Rubber Modified Epoxy Based Composites Reinforced with Alumina Fibers
• 35 Toughening Mechanisms on Recycled Rubber Modified Epoxy Based Composites Reinforced with Graphene Nanoplatelets
• 36 Damage Accumulation in CMCs
• 37 Investigating Intralaminar Crack Growth in Biaxially Stressed Composites
• 38 Determination of Stress Free Temperature in Composite Laminates for Residual Stress Modeling
• 39 Calibration of a Simple Rate Dependent Elastic-Plastic Constitutive Model for a Toughened Carbon Epoxy Composite System
• 40 Imaging the Life-Cycle of CMCs Using High-Resolution X-Ray Computed Tomography
• 41 Effect of Process Induced Residual Stress on Interlaminar Fracture Toughness on Hybrid Composites
• 42 Analysis of Interfaces in AA7075/ Recycled WC Particles Composites Produced via Liquid Route
• 43 Investigation on Microstructure and Interfaces in Graded FE50007 / WC Composites Produced by Casting
• 44 In-Situ Imaging of Flexure-Induced Fracture in Fiber-Reinforced Composites Using High-Resolution X-Ray Computed Tomography